
A project fails. You check the wiring three times. The code is fine. Then the chip turns out to be the problem. Fake and remarked parts are a real headache for students, and they are also a cost for repair technicians. This guide shows what to look at before you solder anything in.
What counts as fake?
- Remarked: old or lower-grade chip, original markings removed, new ones printed.
- Relabelled: a small, cheap transistor given the marking of a power transistor.
- Recycled: a chip pulled from scrap boards, cleaned and sold as new.
- Clone: a different silicon die in a similar package that behaves differently from the genuine part.
Step by step: inspect the part
- Look at the surface. The top of a genuine chip is evenly textured. A remarked one may look shinier, flatter or slightly sanded in patches, sometimes with a visible coating.
- Read the printing under light. Letters should be crisp and even, with the same font and depth across the line. Blurry, crooked, or uneven text is a warning.
- Compare with the datasheet. Check the manufacturer logo, part number format, date code and package. The marking style should match the maker's own datasheet.
- Check the pins. Legs should be clean and uniform. Scratches, bent and straightened legs, or fresh solder on the tips suggest a chip that has been used before.
- Check the moulding. Look for a clean pin-1 dot and consistent corners. Rough edges or leftover paint around the dot are suspicious.
- Try a light rub test. Remarked ink on some fake chips smudges or lifts when wiped gently with a cotton bud and a little isopropyl alcohol. Do this only on a part you are willing to risk, and note that genuine laser marking will not move.
Signs at a glance
| Check | Looks genuine | Looks suspicious |
|---|---|---|
| Top surface | Even texture, consistent finish | Patchy, sanded or oddly glossy |
| Text | Sharp, same depth everywhere | Blurry, crooked, smudges off |
| Pins | Clean, straight, uniform | Scratched, re-tinned, bent back |
| Weight and feel | Same as other chips of that package | Noticeably lighter or hollow-feeling |
| Behaviour | Matches the datasheet in a test circuit | Wrong voltage, runs hot, no output |
Weight and size
Put the suspect part next to a part you already trust in the same package. A power transistor in a TO-220 or metal can package has real heft because it holds a larger die and a thick base. A relabelled small transistor in the same case can feel lighter. For a fair comparison you need a reference part, and a kitchen scale will not help with parts this small, so use your hand and your eye.
Quick multimeter tests for transistors and diodes
A multimeter cannot prove a part is genuine, but it can catch many bad ones. Set the meter to the diode test range.
| Test | Expected result for a good NPN transistor |
|---|---|
| Red on base, black on emitter | Reads a forward voltage drop, roughly 0.5 to 0.8 V |
| Red on base, black on collector | Similar forward drop |
| Reverse the leads on both | Shows OL (open) |
| Collector to emitter, both ways | Shows OL (open) |
For a PNP, swap the lead colours. If a transistor shows a short between any two pins, or reads open where it should conduct, discard it. See our multimeter guide for the full method.
If your meter has an hFE socket, compare the gain with a known good part of the same type. A power transistor that gives a very low gain may be a smaller part with a different label. Treat this as a hint, not proof.
Functional test beats looking
For ICs, the real test is behaviour. Put the chip on a breadboard with a small test circuit from the datasheet. Check the output voltage, current draw and whether it gets too hot to touch within a minute at light load. A regulator that outputs the wrong voltage, or a timer that does not oscillate, is not what the label says.
How to avoid fakes in the first place
- Buy from a shop you can walk back to. A seller who knows you and has a fixed address has a reason to take a complaint seriously.
- Be careful with prices far below the market for the same part.
- Ask for the exact part number and package, and match both when you receive it.
- Keep the bill, especially for expensive or hard-to-find chips.
- Test one piece before buying a bulk lot or building a final board.
Konark Radio Centre, Ashok Nagar, Bhubaneswar has been supplying components since 1995. You can WhatsApp a photo of the part you need, or visit the shop. Starting a first build? See our project kits. Same-day delivery in Bhubaneswar via Rapido is covered on the delivery page.
Frequently asked questions
What is a remarked IC?
A remarked IC is a chip whose original printing has been sanded or chemically removed and replaced with a new part number. It is often a cheaper, slower or lower-grade chip sold as a better one, or a used chip sold as new.
Can a multimeter prove a chip is genuine?
No. A multimeter can only catch obvious problems, such as shorted pins or a transistor that does not behave like its marking. Final proof is the chip working in its circuit as the datasheet says it should.
Are all cheap parts fake?
No. A low price is not proof of a fake, but a price far below what everyone else charges for the same part is a warning sign. Compare, and test before you build the whole board.
What should I do if I think I bought a fake?
Stop using it in your project. Photograph the front, back and pins, keep the bill, and go back to the seller the same day. This is much easier with a shop you can visit than with an anonymous online seller.
Need the parts?
Send the parts list on WhatsApp or walk in. Plot No. 39/F, Ashok Nagar, near Sreeleathers, open 10 AM to 9 PM, all 7 days.